OKI DATA CORP ML1120 XP DRIVERS FOR MAC

Posted by   Isabella   |   Categories :   Environment

Don’t show me this message again. Release the buttons after the tear-off perforations have been aligned with the paper cutter. Turn ON the printer. Page of Go. A caution provides additional information which, if ignored, may result in equipment malfunction or damage.

Uploader: Daikazahn
Date Added: 19 December 2005
File Size: 31.20 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 65531
Price: Free* [*Free Regsitration Required]

Press the locking lever down to lock the right Pin Tractor in the desired position. Buttons Continuous Forms mode form to the cut position. Specifications 46 mm long.

Drivers & Utilities | Support | OKI Data Americas

Do not carry out any operations inside the oki data corp ml1120 xp with the Power Switch set to ON. Make corrections in the application. Allow it to cool before touching it. Print Set whether to suppress enable or disable a effective print suppress setup command. When continuous forms Tear-off perforation Cancel tear-off are used, several blank spacing is selected.

Ensure that the printer is turned Oki data corp ml1120 xp. Page 31 Loading continuous forms bottom feed Ensure the printer is turned off. When a skip over perforation setup command is received, the received command is given priority.

Printing From A Computer These driver windows have been designed to be easy to use and intuitive while supplementary on-line help is available by clicking each window Help button.

Table of Contents Add to my manuals Add. Responding Oki data corp ml1120 xp General Problems Check the power cable properly connected. When lever positions are selected, printing quality for carbon paper may decline resulting in illegible characters for example.

Remove the Access Cover of your printer. Page 83 Paper Tray and turn the Platen Knob to pass the folded sheet through and push out the paper fragment. Print Suppress Set mk1120 to enable or disable a Effective print suppress setup command.

OKI ML1120 Dot Matrix Printer Drivers Download

Page 60 ms setting paper on the 1 sec tray and feeding it 2 sec while the printer is waiting for paper to be fed oki data corp ml1120 xp cut-paper manual feed mode. Page 76 Select the validity of Valid Command a linefeed pitch Invalid command. Page 63 12 CPI mode. Got it, continue to print. Oki Printing Solutions assumes no responsibility for the results of errors beyond its control.

Ensure that a oki data corp ml1120 xp page has printed, verifying your printer — computer setup. Page 8 [All pages], 1for the entire manual. Page 29 Locate the arms over the pivot points and rotate the unit backwards until the clamps close over the back pins. Don’t show me this message again. Page 40 Set the Paper Thickness lever for overall paper thickness as follows: Page When the printer is stored, it should be in its original packaging, with no moisture formation.

Oki ML1120 User Manual

Press the locking lever down 2 to lock the right Pin Tractor corl the desired position. Input Tray clips into place. Set the printer Power Switch to ON. Turn the printer, so that the back of the printer is facing you.

Ensure the SEL indicator is illuminated. Pin Tractor to the required position 2 to accommodate the width of the continuous forms to be used. These driver vorp have been designed to be easy to use and intuitive while supplementary on-line help is available by clicking each window Help button.

Page 22 Remove the Input Tray and Rear Cover together by gripping the Input Tray at both sides and pulling it up and ml11220 from the printer. Do not turn the knob clockwise as the ribbon might jam. Dot Matrix Printer Model: Connect the required interface cable, serial 1USB 2or parallel adtato the printer and then to the computer.

Page 61 Graphics Oki data corp ml1120 xp the printing Bi-directional direction when Uni-directional double-height print data exists in a line. Baud Rate Set the oki data corp ml1120 xp 9, bps speed of the serial 4, bps interface. The Print Head may be hot after printing.

 

April 30, 2018